Shop KLR650 2007 and earlier

 
1 - 36 of 78 items
Sort By:
661 forged piston kit
1987-1995 sprocket retainer plate2007/earlier OEM Kawasaki clutch cable661 forged piston kit

Sprocket retainer plate. Fits ONLY 1987-1995. No longer available from Kawasaki.

OEM Kawsaki clutch cable. Fits 2007 and earlier.

Oversize piston kit, fits all years KLR650. Forged, lightweight, 1mm over stock. Premium rings.

$9.95

$10.99

$299.95

aftermarket cylinder liner for klr650Air filter plastic frameBarnett clutch spring set for klr650

Thicker walls than the stock liner. Fits cylinder blocks for 1996 and later klr650. Requires clearancing of material inside the cylinder block. This is easy to do with dremel or die grinder. Can be bored to 105mm for aftermarket piston. We'll...

OEM plastic foam air filter support

Set of Barnett clutch springs for 1996 through early 2011 klr650 . Set of 5. Different wind, different wire. These work very well. Important - they will NOT measure the same length as the factory springs.

$150.00

$15.99

$16.95

Caliper plate for 320mm rotor, 2007/earlier forks, stock caliper Caliper plate for 320mm rotor, 2007/earlier forks, using SV cali
Caliper plate for 320mm rotor, 2007/earlier forks, stock caliperCaliper plate for 320mm rotor, 2007/earlier forks, using SV calicam bearing bolts - set of 8

adapter plate for 2007/earlier forks, using 320mm rotor and stock caliper.

adapter plate for 2007/earlier forks, using 320mm rotor and SV650 caliper.

Camshaft bearing bolts. Better quality than the OEM parts. Set of 8.

$39.95

$49.95

$6.99

circlip - replacement JEClutch plates OEM Kawasaki 1997-early 2011countershaft collar

Replacement circlip for JE piston kit. This does not fit Kawasaki pistons. This does not fit pistons using spiroloacks to retain the wrist pin.

 

Price is for 2 circlips.

OEM Kawasaki clutch friction plates. Fit mid-1996 to early 2011. Set of 8.

Replacement collar for output shaft, fits into case behind sprocket. Kawasaki part

$3.71

$64.00

$18.99

countershaft collar o-ringcountershaft sealCylinder base gasket - Kawasaki OEM

replacement o-ring for output shaft collar. Kawasaki part.

Replacement seal for countershaft, fit into case behind countershaft sprocket. Kwasaki part.

Genuine Kawasaki OEM cylinder base gasket

$3.49

$5.99

$8.99

cylinder work for 705 or 719dowel for engine cases and cam bearingsdrain plug crush washers, package of 4

Cylinder work for the 719 or 705 piston kit. Does not include liner.

Dowels used all over the klr650 engine. Used as side case locators, and top and bottom of cylinder, and camshaft bearing locators.

Aluminum washers for 12mm drain plug. 

$229.00

$0.49

$1.29

enricher nut or choke nutHead gasket Kawasaki OEMHead gasket Kawasaki OEM Cut for big bore up to 692

replacement plastic enricher nut, or choke cable nut, for the factory carb.

Head gasket, Kawsaki original equipment. Stock (not cut) , so it fits up to 1mm oversize.

Head gasket, Kawsaki original equipment. Cut for over size bore up to 692.

$5.99

$42.99

$47.50

klr cylinder head refurbishOil Filter Bypass Tuberear hub rubber damper

Refurbish your good usable cylinder head. 

Oil filter bypass tube. Often lost, thrown away with the old filter. You need this in the engine to make sure the oil passes through the filter. Only fits one way, small end into the engine first.

Rear hub, rubber damper. This is the rubber part that fits between the sprocket carrier and hub. Kawasaki OEM part.

$160.00

$17.99

$34.99

rings 685Spirolock - replacement JEwaterpump rebuild kit, klr650

replacement ring set for JE/Eagle 685 piston

Replacement spirolock for JE piston kit. This does not fit Kawasaki pistons. This does not fit pistons using circlips to retain the wrist pin.

 

Price is per each - 2 are needed for each piston.

The internal parts needed to rebuild the water pump. O-ring, mechanical seal, and oil seal. You would also likely need a waterpump gasket and clutch cover gasket.

$29.95

$4.77

$18.99

685 forged piston kit 692 forged piston kit 719 forged piston kit
685 forged piston kit692 forged piston kit719 forged piston kit

Oversize piston kit, fits 1996 and later KLR650. Forged, lightweight, 2.5mm over stock. Premium rings.

Oversize piston kit, fits 1996 and later KLR650. Forged, lightweight, 3.00mm over stock. Premium rings.

Oversize piston kit, fits 1996 and later KLR650. Forged, lightweight, 5.0mm over stock. Premium rings.

$299.95

$299.95

$329.99

Complete lever kit with torsion spring incl special tools Complete kit w/torsion spring less tools Basic lever kit (basic doohickey kit)
Complete lever kit with torsion spring incl special toolsComplete kit w/torsion spring less toolsBasic lever kit (basic doohickey kit)

Everything you need except standard shop tools tools!

Kit includes:

Eagle basic lever (Doo) kit (does not include extension springs)

Rotor bolt

Torsion spring

Inner left side gasket

Outer left side gasket

Basic lever kit - the famous Eagle balancer adjustment lever (doohickey). High strength heat-treated aerospace grade stainless. No springs are included. Special tools req'd.

 

$147.95

$108.95

$39.95

Torsion spring Rotor bolt Rotor puller
Torsion springRotor boltRotor puller

Torsion spring for the klr650 balancer system. Offers several advantages over the factory style extension springs: longer adjustment range, captured on install - spring body can't fall into crankcase.

Rotor bolt, genuine OEM Kawasaki.

Rotor puller, made by Eagle! High strength alloy steel. 19mm (also fits 3/4 scket) hex. Don't use those pullers made of soft screw stock, use the good stuff!

$13.95

$16.95

$12.95