Shop Fits all years KLR650

37 - 72 of 80 items
Sort By:
661 forged piston kit 692 forged piston kit 719 forged piston kit
661 forged piston kit692 forged piston kit719 forged piston kit

Oversize piston kit, fits all years KLR650. Forged, lightweight, 1mm over stock. Premium rings.

Oversize piston kit, fits 1996 and later KLR650. Forged, lightweight, 3.00mm over stock. Premium rings.

Oversize piston kit, fits 1996 and later KLR650. Forged, lightweight, 5.0mm over stock. Premium rings.




Complete lever kit with torsion spring incl special tools Complete kit w/torsion spring less tools Basic lever kit (basic doohickey kit)
Complete lever kit with torsion spring incl special toolsComplete kit w/torsion spring less toolsBasic lever kit (basic doohickey kit)

Everything you need except standard shop tools tools!

Kit includes:

Eagle basic lever (Doo) kit (does not include extension springs)

Rotor bolt

Torsion spring

Inner left side gasket

Outer left side gasket

Basic lever kit - the famous Eagle balancer adjustment lever (doohickey). High strength heat-treated aerospace grade stainless. No springs are included. Special tools req'd.





Rotor bolt Torsion spring Rotor puller
Rotor boltTorsion springRotor puller

Rotor bolt, genuine OEM Kawasaki.

Torsion spring for the klr650 balancer system. Offers several advantages over the factory style extension springs: longer adjustment range, captured on install - spring body can't fall into crankcase.

Rotor puller, made by Eagle! High strength alloy steel. 19mm (also fits 3/4 scket) hex. Don't use those pullers made of soft screw stock, use the good stuff!




Rotor holder wrench Left side inner gasket Left side outer gasket
Rotor holder wrenchLeft side inner gasketLeft side outer gasket

Rotor holder wrench used during the lever/doohickey upgrade. Use during rotor bolt removal and with rotor puller to remove rotor from end of crankshaft. Use during install of new rotor bolt. Non-magnetic. Design makes it harder to slip and damage rotor.

left side inner gasket, genuine OEM Kawasaki.

Left side outer gasket. Genuine OEM Kawasaki.




.7" bar risers 1.5" bar risers
.7" bar risers1.5" bar risersexhaust crush gasket

.7 risers, profiled to match KLR triple clamp. Fits KLR650 and others

1.5" bar risers. Machined aluminum, silver or hard black anodized.

Exhaust crush gasket. This is the copper gasket between the cylinder head and the exhaust header. Remember to keep the nuts tight - check the at 100 miles and 500 miles. 




EBC brake pads stainless brake lines EBC 320mm front brake rotor
EBC brake padsstainless brake linesEBC 320mm front brake rotor

EBC braks pads

stainless braided brake lines

320mm front brake for KLR650




Rear master cylinder and brake pedal mount
Rear master cylinder and brake pedal mountNGK Iridium spark plugLow fender Mounting Kit

Replaces the factory cast part with a much stronger machined bracket.

NGK Iridium spark plug. Long lasting, best quality. No need to gap, just install. Hex is 18mm, same as stock. Remember to clean sround the plug with air compressor before removing the old one. There is also a drain hole on the right side of head,...

Low fender mounting kit for use wit the Eagle fork brace.




KLX jet kit Uni air filter Uni air filter care kit.
KLX jet kitUni air filterUni air filter care kit.

KLX needle, main jets, etc

These work very well in the KLR. Flow tests by Cary Aspy said these are the best. Filter care kit available separately. IMPORTANT! You must have the proper oil. Order the filter care kit if you don't have the proper oil. These are not oiled when new!

Keep your engine and filter working well with this kit. Filter cleaner and oil.




Manual Petcock for KLR650 carb screw upgrade kit
Manual Petcock for KLR650carb screw upgrade kitSubframe bolt upgrade

Manual Petcock, replaces factory vacuum petcock. Direct bolt on.

Make your life easier when working on the carb - get these screws!

Non-drill though kit. Replace factory bolts with stronger bolts.




front master cylinder screws Prevailing torque nut
front master cylinder screwsValve shims for KLR650Prevailing torque nut

replacement screws for the front master cylinder reservoir lid.

vavle shims to fit KLR650

prevailaing torque nut for the 1996 and lter KLR650




Countershaft sprocket final drive chain for klr650
countershaft sprocket shim kitCountershaft sprocketfinal drive chain for klr650

Shim kit to remove the lateral play in the countershaft sprocket.

Countershaft sprocket

X-ring final drive chain for klr650




rear sprocket for KLR 650 HiFlo Oil Filter Quick Jack
rear sprocket for KLR 650HiFlo Oil FilterQuick Jack

rear sprocket for klr650 OEM KAwasaki

HiFlo oil filter for the KLR

Also known as a trail jack. Used to support front or rear of bike in combination with sidestand and either wheel. Light, made from steel tubing, fits in a tank bag or tool tube. Telescopes so can be used for any bike.